Quote: Danne wrote in post #38

---

Stick, what do have these days?
Dont think I have seen it.

---

no pics of the new one stick ???

Quote: ebony266 wrote in post #52

---

no pics of the new one stick ???

---

Yea I know your old one, it kept coming up on google allot the last year

HAHA, i used to be high on the googling list but now ive faded off it ...

Took my intercooler off to have another go at fixing a diesel leak....

Was surprised to find a little fan under there....

fitted new stereo

Quote: 123hotchef wrote in post #59

---

---

Wenn Sie hier auf Links zu eBay klicken und einen Kauf tätigen, kann dies dazu führen, dass diese Website eine Provision erhält.

I'm thinking of buying a single din stereo with an LCD screen....

Like this one, less to go wrong than a motorized screen I reckon.

Werbung:

looks good but to be honest I do not use the motorised part much anyway

Wenn Sie hier auf Links zu eBay klicken und einen Kauf tätigen, kann dies dazu führen, dass diese Website eine Provision erhält.

How about one of these bad boys
Werbung:

no manraj. much better off with the jvc. id love a screen but it would cover the drinks holder...... not good. and with 123hotchef's its a little too low for me. looks awesome 123hotchef.

Fitted the 2" lift kit today, finally. It actually turned out to be a lot simpler than I thought it would be, the fitting of the extended brake lines yesterday was the worst part of the whole thing, they actually took longer than the body lift itself.
I followed the 'How to' and '2" body lift' threads (Thanks Stormforce,Stick,Lez) and all went well. The only pipe that I need to replace is the flexi one that runs from the Brake booster along the bulkhead to a metal pipe below the intercooler, (anyone know what that is?), it was just slightly too short, the rest however all managed to take the 2" lift.
All i have to do now is sort out my gear levers, I currently have the whole centre console out, gives it a bit of a 'redneck' look, the gear lever once you uncover it is massive, not too sure how to go about bending that, it's about an inch thick! I also have to raise the winch bumper mounts up 2" then I can finally fit the 285/75/16 STTs I've had in the garage for about 6 months

One thing I would change if I did it again would be not to do it in the middle of winter, my hands have been like blocks of ice for 2 days in a row, and it increases the pain 10 fold when the ratchet slips and you gouge your knuckles

with the gear levers cut a small V and then bend them and get them welded.I will be getting mine done next week
I haven't done any of me extended brake lines yet but will get them done soon though.Should have the shims for adjusting the camber with the ball joint spacers fitted so that will be the complete lift done

Fitted a Parrot MKi9200 kit, at least i wont get pulled over again.

Quote: stormforce wrote in post #66

---

with the gear levers cut a small V and then bend them and get them welded.I will be getting mine done next week

---

once the rubber gaitors are removed you should be able to undo i think 4 bolts and remove the levers from the g/box and trans box

Go easy on cutting them mind, i cut and notched mine quite heavily to get good clearance when in first.

Quote: stormforce wrote in post #69

---

once the rubber gaitors are removed you should be able to undo i think 4 bolts and remove the levers from the g/box and trans box

---

Quote: krutly wrote in post #71

---

Quote: stormforce wrote in post #69

---

once the rubber gaitors are removed you should be able to undo i think 4 bolts and remove the levers from the g/box and trans box

---

Rich, make sure you take some pics when you take the lever out etc and where to cut/weld as I will be doing the same eventually. I have heard a horror story about the "fork" moving and going the "wrong side" of some sort of "selector" in the gearbox. This might be total b@ll@x but just thought I'd mention it.

you could then add the lever mod to the end of your lift instructions

---

Started mocking my head liner, which I took out a few days back, just forgot to order fabric adhesive like a donkey

Quote: dazmanf wrote in post #73

---

Started mocking my head liner,

---

Have to put it inits place Colin, thinks its the head of everything